Author Topic: Ice Comm  (Read 5209 times)

Offline Assaf

  • Sysop
  • Posts a lot
  • *****
  • Posts: 1957
  • Karma: +18/-0
    • scannow.org
Ice Comm
« on: August 09, 2009, 10:47:39 PM »
Ice Comm is my new pet project to create some programming software for the IC-7000. This will be the discussion board for it. When it becomes available for download I will post it here.

Offline azlooker

  • Newbie
  • *
  • Posts: 3
  • Karma: +0/-0
Re: Ice Comm
« Reply #1 on: September 17, 2009, 09:31:51 PM »
Hello Assaf, I am just starting to use ICE to program the IC7000. I am trying to figure out how to import data from the ARRL Travel repeater disk. Other than that, it works well with the Radio Reference interface. Thanks for working on this project. I have been looking for a memory management only program for the IC7000 for a while and this looks and works very well.

Adam

Offline Assaf

  • Sysop
  • Posts a lot
  • *****
  • Posts: 1957
  • Karma: +18/-0
    • scannow.org
Re: Ice Comm
« Reply #2 on: September 17, 2009, 09:39:47 PM »
Hi Adam. Good to hear that it is working for you. I fired up TravelPlus and I was able to bring in the data by doing Edit * Select All then copy, then in Ice Comm using EZ Grab. The only thing is that repeater offsets have to be entered manually right now so that is something I might add in a future version.

Offline azlooker

  • Newbie
  • *
  • Posts: 3
  • Karma: +0/-0
Re: Ice Comm
« Reply #3 on: September 17, 2009, 09:54:52 PM »
Hello Assaf, sounds good to me. I will continue to work with the program. Thanks again for working this up.

Adam

Offline cullenl

  • Newbie
  • *
  • Posts: 1
  • Karma: +0/-0
Ice Comm Working well
« Reply #4 on: May 04, 2011, 11:36:05 AM »
Now I have it working.
Work Sequence
Open Ice comm, a table becomes visible
Click black icon, table vanishes, upload/download box appears
Click DOWNLOAD, this copies present data From Radio to PC
Close upload/download box. Table reappears with data from radio
Save this
Edit data in table to suit.
Save
Click black icon
click Upload, PC to radio
Close Upload/download
close Ice comm
Done.
          Regards, cullen
(Note: Sort function does not move the last item on list)

Offline wx7y

  • Newbie
  • *
  • Posts: 1
  • Karma: +0/-0
Re: Ice Comm
« Reply #5 on: March 23, 2015, 10:37:03 PM »
I know this is a old thread but trying to get ICE to program Different PL tones on the same channel when using the T-SQL settings on a VHF repeater +DUP,
The Repeater RX is 147.660 with a RX PL tone of 123.0Hz, and TX is 147.060 with the TX of PL 88.5Hz.
Setting the IC7000 to the opposite of this on the Memory channel does not work on the TX side.

 Channel settings is shown below

A03   Horn VHF   147.0600   FM-TSQL   1   88.5   123.0   023   NN   True   +DUP   False   147.0600   FM-TSQL   1   88.5   123.0   023   NN   

Thanks in advanced for any help

Bret
WX7Y

Offline Assaf

  • Sysop
  • Posts a lot
  • *****
  • Posts: 1957
  • Karma: +18/-0
    • scannow.org
Re: Ice Comm
« Reply #6 on: March 23, 2015, 10:47:30 PM »
It is an old thread alright! Almost 6 years old. I really haven't used my own program in a very long time since the serial port on my IC7000 blew out and the replacement board is $700. Maybe I will just dump Ice Comm as open source and let the powers of the internet figure it out.